7 Steps to Like-New Floors

7 steps to recoating wood floors and breathe new life into your home.
Avatar:
Old House Online
Author:
Publish date:
Social count:
137
7 steps to recoating wood floors and breathe new life into your home.
After recoating, this room's formerly scuffed-up hardwood flooring (right) looks good as new.

After recoating, this room's formerly scuffed-up hardwood flooring (below) looks good as new.

Nothing defines an old house like hardwood floors—they’re one of the primary features that draws so many of us to antique homes. Regardless of their age or species, wooden floors give a house warmth, character, beauty, and value.

But as every old-house owner has learned, hardwood floors are subject to a great deal of use and abuse. Floors that once gleamed under a flawless coat of clear finish will inevitably become dirty, scratched, stained, and worn. In times past, homeowners would wait until either the finish had nearly worn away or they could no longer stand the sight of the stains and scratches, then would call in the professionals to erase every trace of the old finish with menacing floor sanders.

After the dust had settled, many of these homeowners would soon notice the disparity between their historic house—with its dinged doors, chipped tiles, bruised woodwork and cracked plaster—and their new, seemingly modern wood floors.

In most cases, complete floor refinishing isn’t warranted, yet something needs to be done—and not just for the sake of appearance. A finish does more than just make wood look beautiful. It also seals and protects the wood’s open pores, which, if left exposed, will absorb water, dirt, and spills and will be more likely to be scratched and dented.

Old floor before recoating

Another solution is recoating: adding a new layer of protection that will adhere to the previous finish. Recoating is easier, safer, and faster than refinishing, but it does have its limitations. Since the fresh coat of finish will be applied on top of rather than in place of the existing finish, it can improve the appearance of the old finish, but it cannot solve any problems within the wood itself.

7 Steps to Recoating Wood Floors

To cover up floorboard nails, use a hammer and a fine point (such as a pencil) to drive the nail 1/8" below the surface of the board. Fill the resulting hole with wood putty, allow it to dry (a few hours is usually sufficient), and then sand lightly in the direction of the surrounding grain until it is flush with the wood.

To cover up floorboard nails, use a hammer and a fine point (such as a pencil) to drive the nail 1/8" below the surface of the board. Fill the resulting hole with wood putty, allow it to dry (a few hours is usually sufficient), and then sand lightly in the direction of the surrounding grain until it is flush with the wood.

Step 1: Empty the room.
Don’t attempt to convince yourself you can complete this project by moving furniture around the work area. The room needs to be completely empty—and don’t wait until you bring the floor buffer home. You’ll be paying for it by the hour, so empty the room first.

Step 2: Make any necessary repairs.
This is the time to countersink and fill any exposed nail heads, to plug holes left from old television or phone lines, or to touch up any deep scratches with a wood stain or stain marker.

Step 3: Clean the floor.
In order for a new finish to adhere to an existing finish, any contaminants on the existing finish must first be removed—including, but not limited to, ordinary dirt, grime, grease, dust, soap film, cleaning residue, dusting oils or aerosols, furniture or floor polish, and wax.

Don’t clean with hot, soapy water or any homemade recipes. Harsh chemicals can damage the finish on your floor and baseboards, soap will leave a residue, and excessive water will cause the wood to swell. Instead, use a commercial hardwood floor cleaner designed to dissolve contaminants without dissolving the existing finish. Afterward, scrape the finish with your fingernail to determine if the surface is completely clean.

Step 4: Allow the floor to dry.

A floor polisher fitted with a synthetic pad will make quick work of scuffing old coatings. (Always wear a protective mask to guard against dust particles.)

A floor polisher fitted with a synthetic pad will make quick work of scuffing old coatings. (Always wear a protective mask to guard against dust particles.)

After cleaning, wipe the floor with a soft, dry cloth, and give any remaining hardwood floor cleaner time to evaporate before proceeding. If you are in a hurry, set up a fan to blow air across the floor.

Step 5: Gently scuff the old finish.
Since neither water-based nor oil-based finishes can form a chemical bond with a previous layer of finish, we have to create a mechanical bond between the two finishes by adding thousands of tiny scratches to the existing finish.

Using either a floor polisher and a large synthetic pad, a hand polisher with a synthetic pad, or a palm or orbital sander with 180-grit sandpaper, lightly scuff the surface of the existing finish.

Step 6: Vacuum the dust.
Use the soft bristle attachment on a vacuum to remove the dust created by scuffing. Do not sweep the floor, as a broom or dust mop only pushes the grit into the cracks between the boards.

Using a sponge mop, apply the new finish evenly over the floor, working from the rear corner of the room toward the doorway.

Using a sponge mop, apply the new finish evenly over the floor, working from the rear corner of the room toward the doorway.

Step 7: Apply your chosen finish according to the manufacturer’s instructions.
Choosing the appropriate finish is critical, but regardless of the type of finish you apply, remember that there is a difference between “dry time” and “cure time.” A finish may dry in a matter of minutes, but it will not achieve its maximum hardness until it has had time to cure—typically in about a week.

Once dry, you can walk on the floor in stocking feet, but keep shoes and pets off it for an additional day. If possible, wait three days before bringing in rugs and furniture. And regardless of how long the finish has cured, never slide furniture across a hardwood floor. A worn furniture glide or even a piece of dirt wedged under a chair leg can leave an unsightly scratch in even the strongest finish.

Arts & Crafts expert Bruce Johnsonhas been working with wood finishes for more than 40 years.

Online Exclusive: Wondering what type of finish is right for your project? Click here for tips on choosing one.