Send me a FREE trial issue Plus a FREE gift
Old-House Online » Old-House Tips, Restoration Stories, & More » Repairs & How To » Fix a Rotting Soffit in 7 Steps

Fix a Rotting Soffit in 7 Steps

Follow these 7 simple steps to seamless, long-lasting soffit and cornice repair. Story and photos by John Leeke

    The author used a simple repair technique to fix the rotting soffit on his 100-year-old barn.

    The author used a simple repair technique to fix the rotting soffit on his 100-year-old barn.

    From a distance, it was clear: My century-old barn needed a complete paint job. But after closer examination and a little poking around, I realized the situation was more critical than cosmetic—there were some serious woodwork repairs to be made. More specifically, the soffits and cornices were showing signs of decay. I always approach this kind of work with an organized, step-by-step method that has proven effective over the decades I’ve spent preserving such fine, old structures. No matter if you’re fixing a barn or a historic home, here’s how to mend your soffit ends and cornices to ensure your structure will stand the test of time.

    1. Determine the type and extent of the deterioration

    A: Assess the damage

    A

    The first and most obvious step is to look for rotten wood. Structural movement of the building may shift the cornice woodwork, opening up joints. This breaks the paint film, letting water soak into the end-grain causing checks, splits, and decay.

    The decay is easiest to spot where the wood is completely missing, but be sure to look for other telltale signs. Paint peeling down to bare wood [A] indicates there has been a high concentration of moisture in the wood, perhaps enough to support the growth of fungus. Poke into the wood with a sharp awl or ice pick to discover soft, decayed wood at the surface. Also, tap the surface of the wood with the handle, and listen for the sharp ring of sound wood or the dry hollow thud that indicates a thin (1/16″ to 1/8″) layer of sound wood right at the surface, but rotten wood is underneath.

    Once you find deterioration, determine how far it extends. Often decay and splits are worst at the ends of the boards, with conditions improving further in. Splits usually continue at least a few inches deeper than are first apparent. There also may be deterioration along edges and in the middle of a board, so careful assessment is needed throughout. When you find a decay pocket or a split, look at similar locations where you may discover more of the same.

    B: Cut the deteriorated board

    B

    2. Plan the repairs

    There are four basic types of repair techniques: wood Dutchman (a patch), lap-joint splice, wood-epoxy repair, and complete replacement.

    On my barn project, I knew I’d have some extensive repairs. Every corner of the cornice had decay and splits in the end of at least one soffit board, but thankfully, the rest of the soffits, running about 160 lineal feet, were in good condition. Since less than 1 percent of the length of the soffit boards needed work, it was worthwhile to make spot repairs, instead of considering complete replacement. I used a mix of Dutchman, lap-splicing, and wood-epoxy methods for fixes. Here, I’ll show you how I repaired the end of a soffit board with the traditional lap-joint splice repair method, which removes the deteriorated board end and splices on new wood.

    C: Mark the board using a marking gauge

    C

    First, with a pencil and a combination square, I mark the soffit boards where I need to cut. Then I cut off the deteriorated end of the board [B] and examine the pieces closely to determine if there is more deterioration to remove, in which case, I mark a new joint a few inches along, cut it off, and repeat the process until I hit structurally sound wood.

    3. Design and lay out the joint

    Now that I know the conditions of the board in detail, I can design an effective joint. Here, I’ll use a 3″-long half-lap joint. I lay out the joint with a pencil, combination square and marking gauge (as in Step 2). I mark the shoulder of the lap 3″ back from the end of the board, using the square to make it 90 degrees to the edge of the board. Then, I set the marking gauge for half the thickness of the board and mark the cheek of the joint [C] on the end of the board.

    D: Split away waste from shoulder board

    D

    4. Cut and shape the joint

    Next, I cut the shoulder. The depth of this cut extends only halfway through the board. I like to use a Fein multi-tool fitted with a saw blade, which goes a bit slow, but gives me more control for these tricky cuts. Working with a mallet and sharp chisel, I split away the waste [D] and pare down the surface of the cheek until it is nice and flat.

    5. Create the replacement part

    E: Lay out the new board

    E

    In the shop, I make the replacement part using the old board end as a pattern. The original soffits are made of heartwood Eastern white pine, so I select a board of the same.

    At the end of the boards, I match the annual growth ring pattern so the new board will expand and shrink with changes in moisture content, as the old one did. This will help the joint be more stable and last longer. I trace around the old board [E] to set the shape of the new part, allowing an additional 3″ in length for the lap joint and avoiding defects like knots. Then I shape the part, cutting to the layout marks and overlap depth with a handsaw, hand plane, chisel, and mallet.

    6. Assemble the repair

    Back up on the scaffold, I check the part in place, trim it to fit, and drill shank holes in the new part for screws to hold the joint together. Then I glue it into place with an epoxy adhesive. (Any flexible weatherproof adhesive will work.) After spreading the adhesive, I set the part in place and drive in the screws [F] to hold it tight until the adhesive cures.

    F: Install the new board

    F

    7. Sand and finish

    A light sanding completes the wood lap-joint splice repair, and it’s ready to be painted.

    John Leeke is still working on his barn in Portland, Maine; his wife hopes he’ll finish it one of these years. More details of this repair, the rest of the barn project, and other carpentry solutions can be found on his web site.

    Published in: Old-House Journal May/June 2008

    { 1 comment }

    Lois Belanger June 15, 2014 at 11:46 am

    I need to replace all the soffit boards, it was plywood and I don’t want to use plywood, what kind of wood should I use? thank you



    Get your FREE Trial Issue of Old House Journal and 2 FREE gifts.
    Yes! Please send me a FREE trial issue of Old House Journal and 2 FREE gifts.
    If I like it and decide to continue, I'll get 7 more issues (8 in all) for just $24.95, a savings of 48%. If for any reason I decide not to continue,
    I'll write cancel on the invoice and owe nothing. The Free Trial Issue is mine to keep, no matter what.
     
     Full Name:
     Address 1:
     Address 2:
     City:
     State:
     Zip Code:
     Email (req):
     
    Offer valid in US only.
    Click here for Canada or here for international subscriptions

    Products & ServicesHouse ToursHistoric PlacesHouse StylesOldHouseOnline.comMagazine
    Architectual ElementsKitchen & BathsHistoric HotelsArchitectural TermsRepairs & How ToSubscribe to Old-House Journal
    BathsInterior & DécorHistoric NeighborhoodsAmerican FoursquareFree NewslettersBack Issues
    Ceilings & WallsGardens & ExteriorsHouse MuseumsBungalowSubscribe to Arts & Crafts HomesDigital Editions
    Doors & WindowsColonial RevivalOld House CommunityAdvertise
    Exterior Products & LandscapeGothicAbout Us 
    FlooringQueen AnneContact Us 
    FurnitureVictorianPrivacy Policy
    HardwareLand for Sale
    Heating & CoolingSite Map
    Home Décor
    Kitchens
    Period Lighting
    Real Estate
    Repair & Restoration
    Roofing & Siding
    Tools & Equipment

    EXPLORE OUR HOME GROUP BRANDS:
     
    Designer Sourcw e bookHistoric Home Show Logo

    Copyright © 2011-2016 Old House Online