Send me a FREE trial issue Plus a FREE gift
Old-House Online » Old-House Tips, Restoration Stories, & More » Repairs & How To » Restoration Projects » How To Restore Sash Windows

How To Restore Sash Windows

Restoring your home's original sash windows is easier than it seems. We follow a Texas window restorer to get her tricks of the trade. By Beth Goulart | Photos by Van Ditthavong

    Self-taught window restorer Pam Rodriguez works on a home in Fort Worth's Fairmont Southside Historic District.

    Pam Rodriguez didn’t set out to restore old-house windows for a living. While residing in Massachusetts, Pam learned restoration techniques on the fly, first in an 1875 church she volunteered to help revive, and then in her own home, a 1930s Dutch Colonial in Boston with 22 windows in dire need of repair. A confident do-it-yourselfer, Pam figured out techniques as she went, taking apart sash and frames, making the necessary repairs, then putting it all back together again. “I’m a restorationist at heart,” she says, so she learned to preserve original materials whenever possible.

    In 2005, she returned to her native Texas to be closer to family. Not long thereafter, an acquaintance in Fort Worth’s historic Fairmount neighborhood faced a quandary when she discovered she would need to restore the crumbling old windows in her 1920s Colonial Revival. That turned into a job for Pam, and soon word of her skills got around. Today, she’s Fairmount’s go-to guru of window restoration.

    In the process, she’s run into “all kinds of weirdness,” like a window someone had taken out and reinstalled upside-down. She finds she can fix just about anything, though, if she takes a window all the way down to its frame. “These are old windows that have been here for 70, 80 years,” she says, “and it’s just a matter of a little bit—well, sometimes a lot—of maintenance to make them perfectly good again. If a window has hung in here that long and it hasn’t been totally abused, it’ll be here another 50, 100 years.”

    8 Steps for Restoring Sash Windows

    1. Look for a knockout panel.

    If a window is basically in good shape, needing only to have weights re-hung, Pam looks for a knockout panel (also called a pocket cover), a rectangle scored in the side of the frame that’s typically around 2″ wide and 6″ to 8″ tall—just big enough to pass a weight through. Generally, only higher-end windows have these (many in Fairmount do not). If one exists, though, it’s a handy way to access a sash window’s ropes and weights without removing the trim. Look for a horizontal line between stops in a frame to determine if you’ve got a knockout panel to work through. Especially if it’s been painted, you may have to apply a bit of force along the scored lines with a narrow implement (such as the skinny edge of a 5-in-1 painter’s tool or a box cutter) to open it up, but rest assured that it was, indeed, made for this purpose. (Note: On some windows, knockout panels are held in place by small screws.) If there’s no knockout panel, you may be able to saw one out using an oscillating multi-tool fitted with a wood-cutting blade. If you need to access more than just the weights and ropes, removing any trim around the window is your first step.

    Pam begins the window restoration by removing nails and screws and carefully prying off trim and stops.

    2. Remove trim, stops, and sash.

    The trim and interior stops come off first—hopefully intact. Pam uses a box cutter to cut through any paint and caulk, then begins prying trim from the frame using a 5-in-1 painter’s tool, which she likes because of its narrow dimensions. “I start by breaking the seal with the small pointed tip and turning it, eventually getting the whole narrow edge in so I can gently pry that trim apart,” she says. Do this carefully, easing nails out and removing screws if you find any. Gently apply pressure to pry trim away from the wall. After you’ve created some space, switch to a flat crowbar, again applying gentle force. The bottom sash comes off next. (It’s a good idea to mark this—and all other components—so you can be sure to put the window back together correctly. Pam recommends a fine-tip magic marker used in a spot that’s not going to be sanded or painted.) After that, the parting stops can be removed. Usually these split when Pam takes them out, but she tries to keep them intact if they’re otherwise in perfect condition by using pliers to ease them out once they’re loose. She replaces damaged stops with standard 1/2 ” by 3⁄4″ window trim from the local lumberyard. The top sash comes out last.

    3. Assess the frame.

    Old houses (especially those built on pier-and-beam foundations) have often spent years shifting and settling, so frames are rarely square and snugly fit when Pam exposes them. Moisture also can penetrate the frame’s lower joints, rusting the nails that hold the joints together or rotting the wood, causing the side jambs to drift apart. “Typically the frame is too big,” says Pam. “I’ve almost never found one too small.” Square frames are essential to good window function, so Pam uses a level and a square to correct any twisting, nailing in shims as necessary to create a solidly square frame, but being careful not to place shims near the window-weight well. If shims aren’t enough, she’ll add lattice strips where they won’t show. In the event of a window that’s expanded at the bottom, she finds she can often hide a board on the inside of the bottom of the frame.

    Pam carefully removes glazing compound (which had been painted green along with the window frame) from the sash.

    4. Clean up.

    Pam uses her trusty 5-in-1 painter’s tool to remove debris like old glazing compound, caulk, nails, screws, and broken glass. (A pull-type scraper with a rectangular blade also will work.) Paint, which is often layered so thickly in old houses that it can prevent windows from operating, needs to be sanded or removed at this point, too. (For safety tips on removing lead paint, see “Setting Up for Lead Safety” below.) Paint that’s thin and in good shape often can be left alone. Pam uses a rough sander to cut through thick paint, and in some cases employs a chemical stripper to soften the paint so it’s easier to scrape away. For a fine finish, she uses an orbital sander where possible, but in areas where a more delicate touch is required, such as interior trim with intricate carving work or a sash with routed areas, she relies on hand-applied sandpaper. On those delicate parts, she’ll sometimes use a chemical stripper as well. Once the paint is removed, you can scrape away any rot and fill holes with putty or make repairs with wood epoxy.

    5. Replace damaged or missing glass and glazing compound.

    Original panes that are in good condition can stay intact. “If it’s in good shape, leave it alone!” Pam says. “I’ve broken many windows learning that lesson.” Where replacements are needed, Pam keeps an eye out for discarded wavy glass, since buying reproduction glass can get expensive. If salvaged glass isn’t the exact size she needs, she takes it to the hardware store to have it cut to size. To secure the glass in the sash, Pam loads a caulk-style gun with glazing compound. First, she runs a small bead in the channel, using that to secure the glass without pins or glazier’s points. Then she applies external glazing with the gun, running it along the edge where wood and glass meet. If the product-container tip and the wood edge are both clean, often she can achieve a neat, uniform line that way. Pam advises smoothing down any imperfections with your finger. Then come back the next day, after it’s had plenty of time to harden up, and trim away any excess with a razor blade.

    6. Stain or paint.

    Interior sash can be painted or stained. For the latter, Pam prefers standard oil-based stains like those made by Minwax, and she always tests them on an old or hidden piece of wood to make sure the color is right before applying it to the sash and trim. Getting the right match can be tricky, so sometimes she’ll add a touch of paint with the same type of base as the stain to attain the correct color. A final coat of polyurethane follows the stain to protect the wood. (If the sash and trim are painted, though, no topcoat is necessary.) Exterior sash faces should always be painted for the best weather protection.

    Pam nestles sash rope into an existing hole, then hammers it in place. The length of the rope fits into a routed channel along the sash.

    7. Address pulleys and ropes.

    Weights are often missing from old sash-window frames—some were salvaged for early 20th-century war efforts, while others simply may have slid down inside the wall. Pam likens her pursuit of replacement weights to horse trading—eventually, she finds combinations that work, adding washers or nuts to get the balance right. She typically re-shapes old pulleys with pliers, though if she finds one with a point sharp enough to cut a rope, she will replace it entirely. New or old, pulleys need a regular application of spray lubricant to keep them running smoothly. As a general rule, she says, you should grease a pulley when it squeaks. Any lubricant will work, though one that comes with a skinny spray nozzle is easier to apply. If ropes need replacing, Pam prefers cotton over nylon, because it’s more authentic and tends to stretch less over time. (Plus, nylon has a greater risk of catching on an old pulley.) Purpose-made products labeled as “sash cord” are available, and, as a rule, lighter-weight cord can be used for smaller windows.

    Once both sashes are in place, Pam checks the rope again and adjusts as necessary before replacing the interior stops and trim.

    8. Put it all back together.

    “You’re basically starting over,” says Pam. “You have this wonderful wood sash. You have this wonderful wood frame. And then you put back as much of it as you can.” To reattach stops, Pam chooses nails that are small in diameter (typically 16- or 18-gauge) and just long enough (1/2″ to 3/4 “) to do the job so the nails don’t go through to the weight well. She uses longer finish nails for trim. And unlike many homes’ original builders, she uses as few nails as possible. A sash window goes together in the reverse order it came apart. This means the top sash with its ropes attached goes in first, then weights are tied on. At this point, Pam does an inital check to verify that everything is working properly. “Is something out of place?” she asks herself. “Does something need shimming?” Once confident that everything is in good working order, she replaces the parting stops, the bottom sash, then the interior stops. Finally, she mounts the trim.

    Setting Up for Lead Safety

    If your house was built before 1980, there’s a good chance your windows could contain lead-based paint. Always take the following safety precautions when working with painted windows:

    • Isolate the work area from the rest of the building, and set up a containment area on the floor that extends at least 5′ beyond the work surfaces in every direction. Create the containment, which will help collect and contain dust and debris, by wrapping the edges of 6-mil poly sheeting around 1″ x 2″ wood furring strips.
    • Work “wet” whenever possible. Mist a surface with water before cutting, scraping, or prying lead-painted surfaces. Mist down surfaces where dust and debris fall, and wipe up frequently with paper towels.
    • Wear Tyvek slippers in the containment area, and remove them when stepping out of the containment. Change work clothes before leaving the work area. Always wash work clothes separately from your regular laundry, and double-rinse the machine before starting another load.
    • Wipe the sash and your tools with a damp cloth before you take them out of the containment area.
    • Wear a hat, goggles, and a respirator (N95-rated for wet work, N100-rated for dry work) to keep your hair, eyes, and lungs free of dust. The respirator should fit tightly around your face and completely cover your mouth and nose.
    • Don’t eat, drink, or smoke while you’re working. Thoroughly wash your hands and face each time you leave the containment or work area.
    • For more detailed lead-safe work practices, download “Lead Paint Safety: A Field Guide for Painting, Home Maintenance, and Renovation Work” at

    Adapted from Save America’s Windows by John Leeke, available at

    Online exclusive: Get more tips, tricks, and advice in our Q&A with another window expert.

    Published in: Old-House Journal May/June 2009


    Rod Fowler October 27, 2010 at 12:08 am

    I’m working on 6th Ave. south of Elizabeth Ave. in Ryanwood Place. I have a glazing tool a Dallas window glazier gave me about 12 years ago(for linseed oil glaze). Do you know where I can get some more of those? Not finding them on the net yet.

    Phil May 20, 2011 at 2:57 pm

    I find that once the old glazing has been removed, a light coating of linseed oil is a useful treat before re-glazing dried-out mullions.

    mike smith June 13, 2011 at 2:27 pm

    looking for retro fit window kit, i want to keep old windows and change to double hung window. i saw a show on this old house several years ago. can you help? do you know where i can purchase kit for this project?

    mike smith June 13, 2011 at 2:27 pm

    my house was built around 1757

    venetian blinds brisbane August 17, 2011 at 5:49 am

    Now I can take care of my windows in all conditions. These tips are very useful for us. Now we can improve our home easily and in right way. If you have more tips, then please share with us.

    Pat October 28, 2011 at 7:49 am

    Addressing America’s energy problems and aging infrastructure problems could easily be managed by training all the troops coming home in window technology, and initiating a program to replace all of them to prevent both their hazards and their draftiness. But to do so, a massive investment in window technology to reduce the price of window replacements to affordable levels, and training each returning soldier in replacement technology.

    America’s aging residential and commercial infrastructure about aged windows could be accomplished within two years, virtually eliminating at least one of the problems of the past.

    Catherine Brooks November 28, 2011 at 5:36 pm

    If you are going to train folks, training them to RESTORE old buildings rather than replace them is greener. Restoring old windows is definitely a skill but the old craftspeople are eager to teach their skills to newcomers. If all a program does is rip out old windows, these millions of windows end up in the landfills. The replacement windows are often vinyl and degrade after 10-20 years. Old, wood windows which already have lasted decades and even centuries can be restored to last more.

    Matt M September 1, 2012 at 12:12 am

    I am in the middle of restoring 26 windows on my 1920 craftsman house. Have broken 2 windows in the last two days trying to fix chipping glazing. Learning quick though. In my case people have actually used silicone to hold a couple of my windows in place that have had the ropes break! Then some jerk went around and nailed in all the stops and split most of the cases several different ways. What can be done to fix this? I have been gently prying them apart and cleaning the crack out with air and sand paper. Then injecting liquid nails in the crack and clamping it together. Seems to be working ok. Any better suggestions? Or am I doing this right?

    Catherine Brooks November 19, 2012 at 1:10 pm

    Removing dried glazing without breaking the glass is challenging. Softening it with heat from a heat plate or heat gun first is how it was often done in the past. But the uneven heat created different temperatures across the glass. Where those different temps of glass met, the glass often cracked. Many full-time window people now use low, 400℉ , evenly-distributed, radiant heat from a Speedheater Infrared Paint Remover to prevent the breakage and still soften the glazing for easier chiseling off evenly.

    Mike Johnson December 10, 2012 at 12:25 am

    Does anyone know of anyone that’s in this line of work in the DFW area?

    Nichole Vangelder March 8, 2013 at 11:56 am

    What are these copper/brass button like things around inside of my 1927 windows with a screw inside them? I love them and have seen many in my historic hometown Toledo’s Victorian homes. I need the precise name because I am missing two of these ornate screw eyelets and have to call around asking or search Web……? Thank you…

    Bruce Chu October 24, 2013 at 3:48 pm

    @nichole, those are stop bead adjusters.

    check them out here:

    Davie Jones August 24, 2014 at 3:27 am

    What you mean to tell me that you don’t own a video camera?

    johnson February 21, 2015 at 10:04 am

    Have you or any one you know successfully cut an access panel into a frame; we are in to process of repairing our old, double hung windows & would like to install access panels to facilitate any future rope and weight work that needs to be done. I’d appreciate some pointers.

    Brent hyder March 31, 2015 at 10:17 pm

    Reading the comments on restoring these windows makes me wonder does anybody else out there have a problem with the widespread misuse of the word “glazeing” being applied to putty? Folks, it’s putty that seals the glazing to the woodframe. Glazing refers to glass NOT putty… For some reason we Americans have trouble pronouncing and and getting write our vocabulary. I hope no one takes offense at this criticism…

    charlie April 3, 2015 at 9:23 am

    I restore old wood windows u know repairs people use a lot of putty because they don’t how to make new parts to match what u have cif they can’t fix it right then font mess with iy

    JimmyJames April 10, 2015 at 10:24 pm

    Making me rethink my whole restoration… Did I do my 1920′s colonial revival home a disservice by replacing the old energy inefficient windows with new technology(not vinyl replacements), but new construction wood/aluminum clad. I think not… The plastic on my yet to be replaced windows from this past winter tells me so… Not knocking your trade, I repair reuse refinish wherever possible…

    Diane Floyd July 22, 2015 at 6:27 pm

    Use lace-through scuba weights to replace missing window weights. They are made of lead and come in a variety of weights. They can, with the right equipment, be drilled to accommodate the sash cord but they can also be attached in other ways. They can also be used to increase the weight when the existing weight is too light to counter-balance a new sash. I got new window sashes that weighed 26 pounds and only had two 9 pound weights. Two 4 pound scuba weights did the trick!

    Get your FREE Trial Issue of Old House Journal and 2 FREE gifts.
    Yes! Please send me a FREE trial issue of Old House Journal and 2 FREE gifts.
    If I like it and decide to continue, I'll get 7 more issues (8 in all) for just $24.95, a savings of 48%. If for any reason I decide not to continue,
    I'll write cancel on the invoice and owe nothing. The Free Trial Issue is mine to keep, no matter what.
     Full Name:
     Address 1:
     Address 2:
     Zip Code:
     Email (req):
    Offer valid in US only.
    Click here for Canada or here for international subscriptions

    Products & ServicesHouse ToursHistoric PlacesHouse StylesOldHouseOnline.comMagazine
    Architectual ElementsKitchen & BathsHistoric HotelsArchitectural TermsRepairs & How ToSubscribe to Old-House Journal
    BathsInterior & DécorHistoric NeighborhoodsAmerican FoursquareFree NewslettersBack Issues
    Ceilings & WallsGardens & ExteriorsHouse MuseumsBungalowSubscribe to Arts & Crafts HomesDigital Editions
    Doors & WindowsColonial RevivalOld House CommunityAdvertise
    Exterior Products & LandscapeGothicAbout Us 
    FlooringQueen AnneContact Us 
    FurnitureVictorianPrivacy Policy
    HardwareLand for Sale
    Heating & CoolingSite Map
    Home Décor
    Period Lighting
    Real Estate
    Repair & Restoration
    Roofing & Siding
    Tools & Equipment

    Designer Sourcw e bookHistoric Home Show Logo

    Copyright © 2011-2016 Old House Online